- Air Quality Meter
- Anemometer
- Battery Test Analyzer
- Calibration Tester
- Chart Data Recorder
- Chlorine Meter
- Clamp Meter
- Coating Thickness
- Concrete Meter
- Conductivity Meter
- Current Injection Test
- Current-Echosounder
- Deadweight Tester
- Density Meter
- Dew Point Hygrometer
- Dissolved Oxygen
- Fault Finder Locator
- Flaw Detector
- Flow Meter
- Force Gauge
- Gas Analyzer
- Gauss Meter
- Grain Moisture
- Ground Resistance
- Hand Pump
- Hardness Tester
- High Voltage Rercue
- Hipot Tester
- Holiday Detector
- Insulation Tester
- Leak Detection
- Level Lube Controller
- Light Meter
- Manometer
- Multimeter
- Networks Analyzer
- Ohm Meter
- Oil Content Analyzer
- Oscilloscopes
- Other Products
- PH Meter
- Pipe Cable Locator
- Power Quality Analyzer
- Pressure Gauge
- Rangefinder
- Shaft Alignment
- Sound Level Meter
- Spectrophotometer
- Stroboscope
- Tachometer
- Temp. Calibrator
- Thermal Imager
- Thermohygrometer
- Thermometer
- Torque Tester
- Turbidity Meter
- Ultrasonic Thickness
- Vibration Analyzer
- Video Borescope
- Water Level Meter
- Water Quality Meter
- Weather Station
- Wood Moisture Meter
HIOKI 3285 AC/DC Clamp On Hi-Tester
Harga dapat berubah sewaktu-waktu mengikuti perkembangan kurs rupiah terhadap mata uang asing lainnya sehingga sangat mungkin terjadi adanya perbedaan harga yang berlaku dengan harga yang tertera pada website kami.
AC/DC Clamp On Hi-Tester
Using the external output functions of the 3284 or 3285 in combination with a HIOKI Memory HiCorder enables recording of current and frequency fluctuations and recording and harmonic analysis of instantaneous waveforms. The monitor output (MON) spans a wide frequency range from DC to 20 kHz (15 kHz in the case of 3285), which allows the units to be used for electric current analysis in various fields ranging from batteries to inverters.
The AC+DC mode enables measurement of the RMS value of full- or half-wave rectified waveforms used in electrical machinery.
Features
2000 Arms, clamp aperture: 55 mm dia.
Inrush current crest value
RMS value of full-wave rectified waveforms
Waveform and harmonic analysis
Specification:
AC Current range AC (RMS or Peak value)200.0 or 2000 A AC, 2 ranges (±1.3 % rdg. ±3 dgt. at 50 or 60Hz), AC+DC (RMS or Peak value)200.0 or 2000 A AC, 2 ranges (±1.3 % rdg. ±13 dgt. at 50 or 60Hz), Effective value rectifier
DC Current range DC (Average or Peak value)200.0 or 2000 A DC, 2 ranges (±1.3 % rdg. ±3 dgt.)
AC Voltage range AC (RMS or Peak value)30.00 to 600 V AC, 3 ranges (±1.0 % rdg. ±3 dgt. at 50 or 60Hz), AC+DC (RMS or Peak value)30.00 to 600 V AC, 3 ranges (±1.0 % rdg. ±7 dgt. at 50 or 60Hz), Effective value rectifier
DC Voltage range DC (Average or Peak value)30.00 to 600 VDC, 3 ranges (±1.0 % rdg. ±3 dgt.)
Frequency Measurement: 10 to 1000 Hz, 2 ranges (±0.3 % rdg. ±1 dgt.)
Analog Output DC, or AC 1 V /f.s. ,Level output: with REC mode, Waveform output: with MON mode
Frequency characteristics (at AC current / voltage) DC, 10 to 1 kHz
Display Section Current / 2500 dgt. Voltage / 3750 dgt. Bar graph / 35 seg
Sampling Rate 2 or 4 times/sec (Slow: 1 times/3 sec)
Crest Factor (RMS) 2.5 (1.7 at 600 A range), 1.42 (2000 A range)
Max. Circuit Voltage 600 V AC rms (insulated wire)
Power Supply 6F22(006P) × 1 (Continuous use 25 hours), or AC adapter
Core jaw dia. Ø55 mm(2.17 in)
Dimensions 62 mm(2.44 in)W × 260 mm(10.24 in)H × 39 mm(1.54 in)D
Weight 540 g (19.0 oz)
Accessories 9207-10 TEST LEAD (1), 9345 CARRYING CASE (1), Hand strap (1)

