- Air Quality Meter
- Anemometer
- Battery Test Analyzer
- Calibration Tester
- Chart Data Recorder
- Chlorine Meter
- Clamp Meter
- Coating Thickness
- Concrete Meter
- Conductivity Meter
- Current Injection Test
- Current-Echosounder
- Deadweight Tester
- Density Meter
- Dew Point Hygrometer
- Dissolved Oxygen
- Fault Finder Locator
- Flaw Detector
- Flow Meter
- Force Gauge
- Gas Analyzer
- Gauss Meter
- Grain Moisture
- Ground Resistance
- Hand Pump
- Hardness Tester
- High Voltage Rercue
- Hipot Tester
- Holiday Detector
- Insulation Tester
- Leak Detection
- Level Lube Controller
- Light Meter
- Manometer
- Multimeter
- Networks Analyzer
- Ohm Meter
- Oil Content Analyzer
- Oscilloscopes
- Other Products
- PH Meter
- Pipe Cable Locator
- Power Quality Analyzer
- Pressure Gauge
- Rangefinder
- Shaft Alignment
- Sound Level Meter
- Spectrophotometer
- Stroboscope
- Tachometer
- Temp. Calibrator
- Thermal Imager
- Thermohygrometer
- Thermometer
- Torque Tester
- Turbidity Meter
- Ultrasonic Thickness
- Vibration Analyzer
- Video Borescope
- Water Level Meter
- Water Quality Meter
- Weather Station
- Wood Moisture Meter
METREL MI3201 TeraOhm 5Kv Plus Insulation Tester
Harga dapat berubah sewaktu-waktu mengikuti perkembangan kurs rupiah terhadap mata uang asing lainnya sehingga sangat mungkin terjadi adanya perbedaan harga yang berlaku dengan harga yang tertera pada website kami.
The Metrel MI3201 is used to accurately determine insulation resistance levels on high voltage equipment such as power transformers, high voltage cables, rotating machinery, surge arrestors, measuring transducers and other similar devices.
With multiple test voltages available from 250V up to 5000V (5kV), the MI3201 can be used to accurately measure insulation resistance levels between 5kΩ and 10TΩ. It is also possible to step voltages up by 25V up to 5kV (with ramp testing also available).
Also included as part of this tester are a suite of diagnostic tools for measuring polarisation index (PI), dielectric discharge (DD) and dielectric absorption ratio (DAR) with automated resistance ranging. It is possible to measure all of these parameters at the same time and display them together on the built-in screen.
The MI3201 comes as standard built into its own protective carry case, allowing it to be protected both during a test and after when being transported. It also comes with high EM (noise immunity) ensuring that noisy circuits are filtered out in order to maintain testing accuracy at all times.
Features:
Suite of diagnostic tools - polarisation index, dielectric discharge, dielectric absorption ratio with automated resistance range
Measures insulation resistance from 5kΩ to10TΩ
Display of all measurement parameters in a single measurements
Step voltage testing
R(t) graph shows real time resistance on a time graph for plotting changes over time
High charging capacity with 5mA charging current for charging current insulation systems up to 50μF
High noise immunity to filter out the effects of noise
CAT IV 600V safety rated for use in industrial environments
Rugged hard carrying case
USB and RS232 ports allow interfacing with PC
What's In The Box:
(1) Metrel MI3201 TeraOhm 5kV Plus Insulation Tester
(1) Carrying Bag
(1) Mains Cable
(1) 10kV Shielded Test Leads with Probes (2x, Black/Red)
(2) 10kV Crocodile Clips (Black/Red)
(1) 2m Green Guard Test Lead
(1) Green Crocodile Clip
(6) 1.2V NiMH Batteries - C Type
(1) Handbook "Guide to Modern Insulation Testing" on CD
(1) Instruction Manual
(1) Calibration Certificate