AEMC 6555 (2130.32) 15KV Megohmmeter/ Insulation Tester

Features:
Wide measurement range from 10kΩ to 30TΩ
Fixed or programmable test voltage from 40V to 10kV
5mA charging current
Step voltage testing
Ramp voltage testing
Large backlit graphical LCD screen with digital display, bargraph and R(t)+v(t), i(t) and i(v) graphs
Automatic calculation of DAR / PI / DD /ΔR (ppm/V) ratios
Multiple test modes: voltage ramp and step with "burning", "early break" and "I-limit" modes
Three filters to optimize measurement stability
Calculation of R at referrence temperature
Storage of 80,000 measurements
Optically-isolated USB communication for transfer onto PC and report generation with DataView® software

Applications:
Test insulation on cables, transformers, motors, generators, insulators and wiring installations
High resistance or absorption tests
Spot reading tests
Timed resistance measurements
Dielectric Absorption Ratio (DAR) and Polarization Index (PI) tests
Multi-layer insulation testing (DD)
Test old or water damaged installations over long time periods
Motor insulation resistance measurements
Computer controlled production line testing
Predictive maintenance by storing results on a PC for trend analysis with older tests

The AEMC 6555 15,000V Digital Megohmmeter is a high-end portable measuring instrument intended for the measurement of a wide varity of electrical insulation resistance values on cables and devices operating at high voltage. It is the only fully automated 15,000V graphical insulation tester. The AEMC 6555 is packaged in a rugged case that is IP54 when closed. Test results and configuration information is provided on a graphical LCD screen as well as exportable through the use of DataView® software provided. The AEMC 6555 megohmmeter can operate on battery or AC power while testing. The AEMC 6550 also offers the ability to program up to three step voltage profiles (from 40 to 15,000), each containing up to ten steps. There are also ramp profiles and three programmable test voltages in addition to the standard fixed voltages of 500, 1000, 2500, 5000 and 10,000, 15,000V.

Includes:
Red 9-foot 15kV integral lead
Blue 9ft 15kV integral lead
Black 9ft 15kV integral lead
Red Alligator Clip (100V CAT IV)
Blue Alligator Clip (100V CAT IV)
Black Alligator Clip (100V CAT IV)
Blue Test Probe (100V CAT IV)
Red Test Probe (100V CAT IV)
Optical USB cable
US 115V Power Cord
Small Classic Tool Bag
User Manual

Specifications:
Test Voltage:  500V :  10kΩ to 2000GΩ (2TΩ). 1000V:  10kΩ to 4000GΩ (4TΩ). 2500V: 10kΩ to 10,000GΩ (10TΩ). 5000V: 10kΩ to 15,000GΩ (15TΩ). 10,000V: 10kΩ to 25,000GΩ (25TΩ). 15,000V: 10kΩ to 30,000GΩ (30TΩ)
Fixed Test Voltage:  500/1000/2500/5000/10,000V/15,000
Variable Voltage:  Variable: 40V to 15kV . Three user programmable voltage schemes
Ramp Mode : Programmable ramps:  start voltage/end voltage/duration
Ramp Configuration Range:  40 to 1100V/500 to 15,000V
Step Mode: Up to 10 steps (voltage and duration configurable for each step)
Voltage Measurement After Test : 0 to 2500Vac; 0 to 4000Vdc
Capacitance Measurement:  0.05 t0 9.999µF/10.00 to 49.99µF
Leakage Current Measurement :  0 to 8 mA
Discharge After Test: Yes/Automatic
Additional Test Stop Models: I-Limit:  Programmable: 0.2 to 5mA. early-Break: di/dt. Timer: Up to 99 minutes 59 seconds
Burn Mode: Constant Testing
Ratio Calculation: PI, DAR, DD
Calculation of R at ref. T:  Yes
Measurement Display Filter: 3 filters with 3 possibletime-constants
Graphs on display: R(t)+v(t); i(t); i(v)
Communication: USB optically-isolated port
PC Software: DataView Software
Power Supply: NiMH rechargeable batterries, two 9.6V 4Ah battery packs charging by external voltage: 90 to 260V; 50/60Hz
Battery Charging: Battery Charging allowed while performing insulation measurements
Electrical Safety: 1000V CAT IV; IEC61010-1 and IEC 61557
EMC, Mechanical Protection, Altitude: EN 61326-1, IP54, 3000m
Dimensions: 13.39 x 11.81 x 7.87" (340 x 300 x 200mm)