- Air Quality Meter
- Anemometer
- Battery Test Analyzer
- Calibration Tester
- Chart Data Recorder
- Chlorine Meter
- Clamp Meter
- Coating Thickness
- Concrete Meter
- Conductivity Meter
- Current - Echosounder
- Current Injection Test
- Deadweight Tester
- Density Meter
- Dew Point Hygrometer
- Dissolved Oxygen
- Fault Finder Locator
- Flaw Detector
- Flow Meter
- Force Gauge
- Gas Analyzer
- Gauss Meter
- Grain Moisture
- Ground Resistance
- Hand Pump
- Hardness Tester
- High Voltage Rercue
- Hipot Tester
- Holiday Detector
- Insulation Tester
- Leak Detection
- Level Lube Controller
- Light Meter
- Manometer
- Multimeter
- Networks Analyzer
- Ohm Meter
- Oil Content Analyzer
- Oscilloscopes
- Other Products
- PH Meter
- Pipe Cable Locator
- Power Quality Analyzer
- Pressure Gauge
- Rangefinder
- Shaft Alignment
- Sound Level Meter
- Spectrophotometer
- Stroboscope
- Tachometer
- Temp. Calibrator
- Thermal Imager
- Thermohygrometer
- Thermometer
- Torque Tester
- Turbidity Meter
- Ultrasonic Thickness
- Vibration Analyzer
- Video Borescope
- Water Level Meter
- Water Quality Meter
- Weather Station
- Wood Moisture Meter
PANAMETRICS MTS6 Series Moisture Analyzer
Harga dapat berubah sewaktu-waktu mengikuti perkembangan kurs rupiah terhadap mata uang asing lainnya sehingga sangat mungkin terjadi adanya perbedaan harga yang berlaku dengan harga yang tertera pada website kami.
The GE Panametrics Moisture Target Series 6 is a single-channel analyzer that measures moisture in compressed air and gases. Designed for permanent installations the MTS6 can significantly enhance the performance of OEM products by allowing closed-loop control of moisture. It is used in conjunction with M Series moisture probe or VeriDri moisture transmitter for air/gas dryer original equipment.
The microprocessor-based MTS6 accurately tracks fast-changing process conditions and displays dew/frost point temperature in °F or °C on an LCD. Dew/frost point is also available as an analog voltage or current output, and the Moisture Target Series 6 features built-in isolation to ensure the integrity of signals to remote devices. The unit also features two Form C alarm relays for high and low dew/frost point limits. The microprocessor-based electronics and six-button keypad combine to make selection of analog output zero and span, alarm setpoints fast and easy, and entry of calibration data sample.
The panel-mount MTS6 comes in a compact DIN standard meter housing for applications where space is at a premium. The case slides directly into the panel cutout, and is held in place from the rear by captive screws.
Features:
Low-cost, single-channel hygrometer for OEM applications
Compatible with M Series moisture probe or VeriDri moisture transmitter
NEMA 4 weatherproof membrane front display/keypad
Built-in isolated current or voltage analog output
MicroSD card for logging data up to 32 GB
Panel-mount and board-level configurations
Alarm Relays
One fail-safe fault relay
Two standard Form C relays SPDT, rated for 3 A at 250 VAC/30 VDC
Set to any level within the range of the instrument; programmable from the front panel
128 x 64 matrix LCD display
Displays dew point temperature in °F, °C or sensor signals for diagnostics
Standard switch-selectable outputs
0 to 2 V, 10kΩ minimum load resistance
0 to 20 mA, 400Ω maximum series resistance
4 to 20 mA, 400Ω maximum series resistance
User-programmable within the range of the instrument and the corresponding sensor or transmitter
What's In The Box:
(1) Power Supply
(1) Instruction manual
(1) Transducer cable
(1) Couplant
(1) Traceable calibration certificate