- Air Quality Meter
- Anemometer
- Battery Test & Analyzer
- Calibration Tester
- Chlorine Meter
- Clamp Meter
- Coating Thickness
- Concrete Meter
- Conductivity Meter
- Current & Echosounder
- Current Injection Test
- Deadweight Tester
- Density Meter
- Dew Point Hygrometer
- Dissolved Oxygen
- Fault Finder Locator
- Flaw Detector
- Flow Meter
- Force Gauge
- Gas Analyzer
- Gauss Meter
- Grain Moisture
- Ground Resistance
- Hand Pump
- Hardness Tester
- High Voltage Rercue
- Hipot Tester
- Holiday Detector
- Insulation Tester
- Leak Detection
- Level Lube Controller
- Light Meter
- Manometer
- Multimeter
- Networks Analyzer
- Ohm Meter
- Oil Content Analyzer
- Other Products
- PH Meter
- Pipe Cable Locator
- Power Quality Analyzer
- Pressure Gauge
- Rangefinder
- Shaft Alignment
- Sound Level Meter
- Spectrophotometer
- Stroboscope
- Tachometer
- Temp. Calibrator
- Thermal Imager
- Thermohygrometer
- Thermometer
- Torque Tester
- Turbidity Meter
- Ultrasonic Thickness
- Vibration Analyzer
- Video Borescope
- Water Level Meter
- Water Quality Meter
- Water Sampler
- Weather Station
- Wood Moisture Meter
ELCOMETER 266-15 DC 0.5 to 15KV Portable Holiday Detector
Harga dapat berubah sewaktu-waktu mengikuti perkembangan kurs rupiah terhadap mata uang asing lainnya sehingga sangat mungkin terjadi adanya perbedaan harga yang berlaku dengan harga yang tertera pada website kami.
The Elcometer 266 revolutionises high voltage DC testing of coatings porosity detection making it safer, easier and more reliable than ever before.
The Elcometer 266 holiday detector can be used to test porosity on coatings up to 7 mm (275 mils) thick and is ideal for inspecting coatings on pipelines and other protective coatings.This holiday tester features a built-in voltage calculator which will determine and set the correct test voltage based upon the test standard and the thickness of coating being tested.
Elcometer 266 Features
Voltage calculator automatically sets the correct voltage from your coating thickness value
No need to use look up tables. Enter the test standard and the coating thickness and the gauge will automatically programme the correct voltage.
Voltage adjustable using the keypad - no need for screwdriver: 0.5kV - 1kV in 50V steps, 1kV to 30kV in 100V steps
Sensitivity to current can be manually preset or automatically adjusted by the gauge for partially conductive coatings.
Internal Voltmeter/Jeep tester ensures that the test voltage equals the selected voltage
The closed loop system ensures that the generated test voltage is accurately measured and continuously controlled, regardless of climatic conditions.
Interchangable probes handles are available, 5kV, 15kV and 30kV DC Versions
Audible and visual alarms are activated when a flaw is detected
Bright LEDs on the handle, as well as a loud audible alarm, clearly indicate if the gauge is on (Red) and when a spark is detected (Blue).
Battery packs can be recharged inside or outside the gauge for continued use
Batteries are fully charged within 4 hours and provide up to 40 hours continuous use between charges.
Adaptor enables use of accessories from other manufacturers
Elcometer 236 & Elcometer 136 Models AP, APS, AP/S1 & AP/S2
Models 780, 785 & 790 Models 10/20 & 14/20 Compact DC & Compact Pulse
Large, backlit display enables easy viewing even in dark environments. When a flaw is detected the backlight also flashes.
Interchangeable handles: 0.5 - 5kV, 0.5 - 15kV or 0.5 - 30kV adjustable in 0.1kV steps.