- Air Quality Meter
- Anemometer
- Battery Test & Analyzer
- Calibration Tester
- Chart & Data Logger
- Chlorine Meter
- Clamp Meter
- Coating Thickness
- Concrete Meter
- Conductivity Meter
- Current & Echosounder
- Current Injection Test
- Current Load Bank
- Deadweight Tester
- Density Meter
- Dew Point Hygrometer
- Dissolved Oxygen
- Fault Finder Locator
- Flaw Detector
- Flow Meter
- Force Gauge
- Gas Analyzer
- Gauss Meter
- Grain Moisture
- Ground Resistance
- Hand Pump
- Hardness Tester
- High Voltage Rercue
- Hipot Tester
- Holiday Detector
- Insulation Tester
- Leak Detection
- Level Lube Controller
- Light Meter
- Manometer
- Multimeter
- Networks Analyzer
- Ohm Meter
- Oil Test Analyzer
- Oscilloscope
- Other Products
- PH Meter
- Pipe Cable Locator
- Power and Voltage
- Power Quality Meter
- Pressure Gauge
- Rangefinder
- Shaft Alignment
- Sound Level Meter
- Spectrophotometer
- Spectrum Analyzer
- Stroboscope
- Tachometer
- Temp. Calibrator
- Thermal Imager
- Thermohygrometer
- Thermometer
- Torque Tester
- Turbidity Meter
- Ultrasonic Thickness
- Vibration Analyzer
- Video Borescope
- Water Level Meter
- Water Quality Meter
- Water Sampler
- Weather Station
- Wood Moisture Meter
HIOKI 3665-20 LAN Cable Hi Tester
Harga dapat berubah sewaktu-waktu mengikuti perkembangan kurs rupiah terhadap mata uang asing lainnya sehingga sangat mungkin terjadi adanya perbedaan harga yang berlaku dengan harga yang tertera pada website kami.
Identify the 3 most important criteria for proper networking at a glance
Wire map check : Detect split pairs with wiring check
Cable length : Get NVP-Enhanced measurement accuracy
Direction check : Identify up to 21 cable destinations
Basic specifications
Measurable cable Twisted-pair cable
100ohm characteristic impedance, shielded and unshielded,
CAT 3, 4, 5, 5e and 6
Compatible connectors RJ-45 plugs
WireMap check Wiring condition and shielding can be confirmed using the HIOKI TERMINATOR 9690
Detectable errors: open, short, reversed, transposed, split pairs and other miswiring
Cable length check Measurable lengths: 2 to 300 m, 6.6 to 984 ft
Measurement accuracy: ± 4% rdg. ± 1 m, ± 4% rdg. ± 3.3 ft
Display resolution: 0.1 m, 0.3ft
Direction check Up to 21 cables can be identified using the supplied TERMINATOR 9690 and optional Models 9690-01 to 9690-04
Display 128 x 64 dot matrix LCD ( with backlight)
Functions Auto Backlight: pressing a button turns the backlight on ( it turns off automatically after about 20 seconds)
Beeper: sounds when pressing buttons and when measurement results are displayed
Energy-Saving Mode: enter into energy-saving mode after measurement ( and resume when the TEST button is pressed)
Auto Power Save: the 3665-20 turns off automatically about 10 minutes after the last button press
Battery Check: Battery indicator blinks when voltage falls below 2.4 V
Unit Switch: Select between meters or feet
Power supply Two AA-size ( LR6) alkaline batteries 1.4VA Approx. 50 hours
Dimensions, mass Approx. 85 W x 130 H x 33 D mm, approx. 160 g
Accessories TERMINATOR 9690 ( 1)
CARRYING CASE( 1) ( Stores the HiTESTER 3665-20 and TERMINATORs 9690)